KFN-KABUTO-FINELIVE-CENTER-with-NUT---NC-LATHE-02
KABUTO

KFN KABUTO FINELIVE CENTER with NUT – NC LATHE

  • Structured to keep cutting water away by means of air film resulting from rotation.
  • The product with light running torque is most suitable for fine machining or light metal working.
  • The replacement head enables cost reduction.
Download Catalogue
Categories: ,
NC Lathe Center Head Replaceable Type

  • See Technical Specifications (HEAD LIST) for center head types.
  • See Technical Specifications  (ALLOWABLE LOAD & MORSE TAPAR) for revolutions per minute.
  • Type KFN has the same waterproof structure as that of type KFL.
  • Type KFN comes with the carbide center head A and then the center head ejecting drift DHN-1
    (while KFN-5 comes with the carbide center head 5A60° and DHN-2).
DIMENSIONS TABLE   (UNIT mm)
MODEL TYPE M.T. φD1 φD φd φh A B C E F J L HEAD TYPE WEIGHT (g)
KFN-3 No.3 60 48 30 16 36.2 36 84 1.5 22.5 24 156.2 REPLACEMENT 1,240
KFN-4 No.4 79 63 32 16 40.2 45.5 105.5 1.8 26.5 31.5 191.2 REPLACEMENT 2,330
KFN-5 No.5 105 85 52 26 60.5 54 132 2.3 38 37 246.5 REPLACEMENT 5,150

* Dimensions are subject to change for alteration without prior notice.

 

 

  • The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

 

DIMENSIONS TABLE  (UNIT mm) 
* For KFN-A, B, please choose steel (tempered product) or with carbide.
MODEL TYPE M.T. φD1 φD φd A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER
KFN-3A No.3 60 48 28 37 36 84 1.5 24 157 INTEGRAL 1,280 φ12
KFN-4A No.4 79 63 32 40 45.5 105.5 1.8 31.5 191 INTEGRAL 2,440 φ14
KFN-5A No.5 105 85 42 55 54 132 2.3 37 241 INTEGRAL 5,080 φ18

* Dimensions are subject to change for alteration without prior notice.

 

 

  • The photo and dimensional drawing show the rigid (quenched) head, but the carbide head is also available.

 

DIMENSIONS TABLE  (UNIT mm) 
* For KFN-A, B, please choose steel (tempered product) or with carbide.
MODEL TYPE M.T. φD1 φD φd φh A B C E J L HEAD TYPE WEIGHT (g) CARBIDE DIAMETER
KFN-3B No.3 60 48 25 10 41.5 36 84 1.5 24 161.5 INTEGRAL 1,180 φ7
KFN-4B No.4 79 63 32 12 52 45.5 105.5 1.8 31.5 203 INTEGRAL 2,410 φ10
KFN-5B No.5 105 85 42 20 65 54 132 2.3 37 251 INTEGRAL 5,120 φ14

* Dimensions are subject to change for alteration without prior notice.

HEAD LIST

HEAD LIST

 

LOAD CAPACITY & MORSE TAPAR TABLE

ASSUME BEARING LIFE OF 2000 HOURS   (UNIT kgf)

KFL & KFN

KFL
KFN
 MORSE TAPER LOAD / rpm 500 1,000 2,000 3,000 4,000 5,000 6,000 7,000
M.T.-3 RADIAL 330 238 192 161 146 137 129 96
THRUST 196 140 113 95 86 81 75 60
M.T.-4 RADIAL 527 419 332 290 264 244 230 172
THRUST 300 238 189 165 150 139 130 104
M.T.-5 RADIAL 705 577 454 409 360 325 306 230
THRUST 470 385 303 273 240 217 204 153

KS & KSN

KS
KSN
 MORSE TAPER LOAD / rpm 500 1,000 2,000 3,000 4,000 5,000
M.T.-2 RADIAL 168 135 107 93 84 78
THRUST 221 177 140 122 111 104
M.T.-3 RADIAL 237 190 151 132 120 110
THRUST 312 250 198 173 157 145
M.T.-4 RADIAL 425 340 268 235 213 198
THRUST 556 445 353 308 280 260
M.T.-5 RADIAL 630 504 400 349 317 294
THRUST 780 662 525 460 417 387

KC & KCW

KC
KCW
 MORSE TAPER LOAD / rpm 50 150 500 1,000 2,000 3,000
M.T.-1 RADIAL 53 29 24 20 16 12
THRUST 55 37 29 23 20 15
M.T.-2 RADIAL 212 115 95 77 61 48
THRUST 282 189 148 112 97 77
M.T.-3 RADIAL 340 200 160 125 108 86
THRUST 430 298 237 191 155 124
M.T.-4 RADIAL 643 380 302 231 206 164
THRUST 665 445 352 280 245 194
M.T.-5 RADIAL 910 605 485 385 308 –
THRUST 1065 713 564 450 360 –
M.T.-6 RADIAL 2800 2100 1380 1170 – –
THRUST 3750 2770 1850 1470 – –

【NOTES】 Load capacity is a value that shows the lifetime limitation of the bearing, and is therefore not a value for the center itself.

 

MORSE TAPER TABLE

MORSE TAPER GAUGE LINE ONE-SIDED TAPER ANGLE TAPER RATIO
No.1 Ø 12.065 1° 25′ 43″ 0.049882
No.2 Ø 17.780 1° 25′ 50″ 0.049951
No.3 Ø 23.825 1° 26′ 16″ 0.050196
No.4 Ø 31.267 1° 29′ 15″ 0.051938
No.5 Ø 44.399 1° 30′ 26″ 0.052626
No.6 Ø 63.348 1° 29′ 36″ 0.052138

Related products